Part 2
54. Remove the throttle body.
^ Remove and discard the gasket.
55. Disconnect the exhaust gas recirculation (EGR) valve electrical connector.
56. NOTE: Cap the exposed ports.
Disconnect the coolant hoses.
57. Remove the EGR valve and the exhaust manifold to EGR valve tube.
^ Remove the retaining bolts.
^ Remove and discard the exhaust manifold to EGR valve tube gasket.
^ Remove and discard the EGR valve to air intake elbow gasket.
58. Disconnect the air intake elbow pipes.
59. NOTE: Make sure correct location of the ground strap is noted.
Remove the air intake elbow retaining bracket lower retaining bolts.
60. Detach the air intake elbow.
^ Remove and discard the gasket.
^ Remove and discard the retaining bolt seals.
61. Remove the air intake elbow.
^ Disconnect the manifold absolute pressure (MAP) sensor.
62. Remove the supercharger.
63. CAUTION: Make sure no foreign matter enters the cylinder head ports.
NOTE: Right-hand shown, left-hand similar.
Remove the charge air coolers.
^ Remove and discard the charge air cooler gasket.
64. Disconnect the knock sensor electrical connectors.
65. NOTE: Left-hand shown, right-hand similar.
Remove the ignition coil cover.
66. Remove the engine cover retaining bracket.
67. Remove the engine cover retaining bracket.
68. NOTE: Right-hand shown, left-hand similar.
Detach the engine wiring harness.
69. NOTE: Right-hand shown, left-hand similar.
Disconnect the fuel injector electrical connectors.
70. Disconnect the ignition on-plug coil electrical connectors.
71. Detach the engine wiring harness.
72. Detach the engine wiring harness.
73. Disconnect the camshaft position sensor electrical connector.
74. Detach the engine wiring harness.
^ Detach the ground cable.
^ Disconnect the variable valve timing (VVT) solenoid electrical connector.
1. Detach the engine wiring harness.
75. Detach the engine wiring harness.
^ Remove the retaining bolt.
76. Detach the engine wiring harness.
77. Disconnect the positive crankcase ventilation pipe.
78. Disconnect the fuel pressure regulator electrical connector.
79. Disconnect the exhaust gas recirculation valve electrical connector.
80. Disconnect the exhaust gas recirculation valve coolant hose.
81. Detach the engine wiring harness.
82. Disconnect the fuel injector electrical connectors.
83. Detach the engine wiring harness.
84. Disconnect the ignition on-plug coil electrical connectors.
85. Disconnect the fuel temperature sensor electrical connector.
86. Disconnect the camshaft position sensor electrical connector.
87. Detach the engine wiring harness.
88. Detach the engine wiring harness.
89. Remove the intake manifold.
90. Remove the lower intake manifold.
91. NOTE: Place a suitable container underneath the filter to prevent oil spillage.
Remove the oil filter element.
92. Remove the oil cooler.
^ Remove and discard the O-ring seal.
93. Disconnect the oil pressure switch and oil temperature sensor electrical connectors.
94. Remove the oil filter housing.
^ Remove and discard the O-ring seal.
95. Detach the right-hand oxygen sensor.
96. Detach the engine wiring harness retaining clips.
97. Remove the engine wiring harness.
98. Remove the noise and vibration insulating pad.
99. Remove the intake manifold heater coolant hose.
1. Remove the knock sensors.
2. Remove the intake manifold heater coolant hose.
100. Remove the engine block insulation grommet.
101. Remove the water pump pulley.
^ Using the special tool, retain the water pump pulley.
102. Remove the water pump.
^ Remove and discard the gasket.
^ Remove and discard the O-ring seal.
103. Remove the thermostat housing.
^ Remove and discard the O-ring seals.
104. NOTE: Left-hand shown, right-hand similar
Remove the ignition coils.
105. Remove the spark plugs.
106. Remove the right-hand camshaft position (CMP) sensor.
^ Remove and discard the O-ring seal.